Dhs-Sp Power Generation System Charge Controller

Produktbeschreibung

Main features
1. The new Solar Charge Controller remote control design, the wireless control distance can be up to 10 meters, and the controller parameters can be modified by remote control;
2. Data communication adopts multiple handshake protocol and Run Length Encoding to make data transmission accurate and fast;
3. The wireless reading controller runs parameters to facilitate the quick maintenance and operation of the system;
4. Support 12V24V lead acid battery, 3 series of lithium battery, 4 series of LifePO4 battery, customizable parameters;
5. Enable the activating function of lithium battery protection, and can open the load at any time by manual remote control;
The maximum efficiency of the constant current source is 96%.
7. Intelligent 5 segment dimming light, power adjustment more accurate, color temperature performance more outstanding;
8. The battery is equipped with low voltage protection, intelligent power output, and effective protection of lighting time;
Excellent current ripple control and load linearity control, minimizing LED light failure and lengthening LED life.
10. Improved charging algorithm, charging more efficiency, making solar energy use time longer;
11. 12V battery suitable for 3 series lamp beads ,24v battery suitable for 6 series lamp beads;
12. Low temperature charging protection of lithium, when the ambient temperature is below zero, it can be set to stop low temperature charging and effectively protect the battery;
13. Enhanced battery anti-grafting protection, LED short-circuit protection, open road protection, etc., to make the system fully and effectively protected;
Not only support external temperature compensation, internal PCB has the temperature protection and recovery function;
15. Organic thermal conductivity silicone seal, IP68 waterproofing grade, can be used in all kinds of bad environment, industrial grade quality guarantee;
16. The high power density design of the metal shell gives the maximum power to the unit volume, while it can effectively control the temperature rise;
17. Support external photocontrol trigger (need to add modules), support human infrared or microwave induction (additional modules are required).

Technical parameters

Accumulator voltage	Colloid, open battery	Ternary lithium battery		Lithium iron phosphate battery
	12V/24V	3.7V*3S		3.2V*4S
Rated charging current	10A
Rated power	12V->max40W /×2/24V ->max80W
The output current	Parameters can be modified, by default: 150mA
open circuit voltage	< 55V
Overcharge protection voltage	14.5V/29.0V		12.5V		14.4V
Overcharge recovery voltage	14.0V/28.0V		12.3V		14.2V
Charge voltage	13.8V/27.6V		12.2V		14.2V
Floating charging voltage	13.2V/26.4V		12.0V		14.0V
Overshoot protection voltage	11.0V/22.0V		9.6V		10.4V
Overrelease voltage	12.5V/25.0V		11.1V		12.8V
Low voltage protection voltage	12.0V/24.0V		11.1V		12.8V
Light control turn on lamp voltage	5.0V/10.0V		5.0V		5.0V
Light control lamp voltage	7.0V/14.0V		7.0V		7.0V
Manual switch	Parameters can be modified, default: off, light control mode
Intelligent reduced power	Parameters can be modified, default: yes
Sub-zero charge	Parameters can be modified, default: yes
No-load loss	≤10mA
Number of lights in series	12V->3 /2 / 24V -> 6 (customizable)
Working temperature	-35ºC--+65ºC;
Protection grade	IP68
The net weight	0.25Kg
Diameter and length	1.5mm²,≤100mm
Size (length x width x height)	68×84×21mm

Installation and wiring
1. First, the LED lamp head is connected with the negative pole to correspond to the lamp red black line;
2. In the same time, the battery is connected to the controller with the battery red and black line, and the controller has three instructions to enter the work.
3. Wait 60 seconds for the lamp to be bright, and then the solar panel is connected with the negative pole to the red black line of the panel.
4, if the day is installed, wait 60 second turn off the light to enter charge status, if the evening installation will continue to light the lamp, the installation is finished;
Remove the controller and install the reverse order.
The installation diagram is as follows:

State indication

LED indicator	Light color	Indicates	The content status	Function
	Yellow	Discharge	Normally bright	Output normal
			Quick flash	Load short circuit protection
			Slow flash	Load opening protection
	Red	Battery power	Always bright	Battery is normal
	Red	Battery power	Quick flash	Over-discharge protection
	Green	Charging	Slow flash	Charging
			Quick flash	Input overpressure, no charge
			Always bright	Voltage is higher than the turn-off voltage, no charge
			Off	The voltage is lower than the turn-on voltage

Note: 1. The load short circuit opens to the protection, and after 2 minutes, the detection failure exists. If there is any further protection, the load will be turned on.

Load requirements

System voltage	The number of light beads in series	Load output power
12V	S=3	PLED ≤40W
24V	S=6	PLED ≤ 80W

Note: 1. 3 series 3.7 V lithium battery corresponding to the voltage load requirement of 12V system;
2. 4 series 3.2 V iron phosphate battery corresponding to the voltage load requirement of 12V system;

Load working mode
The load working time can be divided into five periods, each working time and work power can be adjusted arbitrarily. Different combinations can achieve different control modes.

Adjustment item	parameters	Recognition Value	the output current of the factory will be 150mA, and the power adjustment step will be 10%, and the time will be adjusted to 10min.
The first power	0 ~ 100% rated power	100% rated power
The first paragraph	0~999min	120min
Phase 2 power	0 ~ 100% rated power	50% rated power
The second period	0~999min	240min
Section 3 power	0 ~ 100% rated power	0
The third period	0~999min	0
Section 4 power	0 ~ 100% rated power	0
The fourth period	0~999min	0
Phase 5 power	0 ~ 100% rated power	0
Period 5	0~999min	0

1. Routine optical control timing mode: for example, the lights are black and light for 4 hours, the first 2 hours full power, and the second half power.
Setting: the first power is "100% rated power", the first period is "120min"; The second part is "50% rated power" and "120min" in the second period; The rest of the power time is "0".
2. Electric timing + morning light pattern: cases required day black lights 4 hours, 2 hours before the full power, power, in about two and a half hours after the morning 2 hours before dawn full power lights, the whole night about 10 hours;
Setting: the first power is "100% rated power", the first period is "120min"; The second part is "50% rated power" and "120min" in the second period; The third power is "0" and the third period is "240min". The fourth part is "100% rated power" and the fourth period is "120min". The rest of the power time is "0".
3. Delay electric timing + morning light pattern: example to delay for 30 minutes, dark and light 4 hours, 2 hours before the full power, power, in about two and a half hours after the morning 2 hours before dawn full power lights, the whole night about 10 hours;
Setting: the first power is "0", the first period is "30min"; The second part is "100% rated power" and the second period is "120min". The third part is "50% rated power" and the third period is "120min". The fourth part is "0" and the fourth period is "210min". The fifth stage power is "100% rated power" and the fifth time is "120min".

Note: this controller has a battery low voltage intelligent power function, when the battery voltage is less than the controller setting "low voltage protection value" to step down power output 10%, until to 10% power, the end of the light or battery discharge protection.

Matters needing attention
1. It is strictly forbidden that the output voltage of the controller can be caused by excessive output voltage when the output voltage is too high.
2. The controller has set relevant parameters, and the LED lamp is connected to ensure that the parameters are aligned with the controller, otherwise the controller will be damaged or the LED lamp will be burned.

Lieferfähigkeit

Verpackung und Versand

Vorlaufzeit:

Hafen:

Verpackungsdetails:

>=5 pieces

US 7.00-8.00

Kontakt

Kommentare

Willkommen bei unzuun Kommentaren! Bitte halten Sie die Gespräche höflich und thematisch. Um produktive und respektvolle Gespräche zu fördern, Sie können Kommentare von unseren Community Managern sehen.

>={ {

US {-{

Details anzeigen