Dhs-Wp Waterproof Intelligent Solar Charger Controller

Produktbeschreibung

Main features
1. The new Solar Charge Controller remote control design, the wireless control distance can be up to 10 meters, and the controller parameters can be modified by remote control;
2. Data communication adopts multiple handshake protocol and Run Length Encoding to make data transmission accurate and fast;
3. The wireless reading controller runs parameters to facilitate the quick maintenance and operation of the system;
4. Support 12V24V lead acid battery, 3 series of lithium battery, 4 series of LifePO4 battery, customizable parameters;
5. Enable the activating function of lithium battery protection, and can open the load at any time by manual remote control;
The maximum efficiency of the constant current source is 96%.
7. Intelligent 5 segment dimming light, power adjustment more accurate, color temperature performance more outstanding;
8. The battery is equipped with low voltage protection, intelligent power output, and effective protection of lighting time;
Excellent current ripple control and load linearity control, minimizing LED light failure and lengthening LED life.
10. Improved charging algorithm, charging more efficiency, making solar energy use time longer;
11. The output voltage of this solar controller is the same as the battery voltage, suitable for 12 V or 24 V load. A large number of applications in the solar streetlight system, solar insecticidal lamp system, solar energy monitoring system and so on.;
12. Low temperature charging protection of lithium, when the ambient temperature is below zero, it can be set to stop low temperature charging and effectively protect the battery;
13. Enhanced battery anti-grafting protection, LED short-circuit protection, open road protection, etc., to make the system fully and effectively protected;
Not only support external temperature compensation, internal PCB has the temperature protection and recovery function;
15. Organic thermal conductivity silicone seal, IP68 waterproofing grade, can be used in all kinds of bad environment, industrial grade quality guarantee;
16. The high power density design of the metal shell gives the maximum power to the unit volume, while it can effectively control the temperature rise;
17. Support external photocontrol trigger (need to add modules), support human infrared or microwave induction (additional modules are required).

Technical parameters

Accumulator voltage	Colloid, open battery	Ternary lithium battery		Lithium iron phosphate battery
	12V/24V	3.7V*3S		3.2V*4S
Rated charging current	5A/10A/15A/20A
Overload, short circuit protection	@1.25 times rated current 30 second protection; @1.5 times rated current 10 second protection; At least 3 times the rated current is protected immediately
Open circuit voltage	< 55V
Overcharge protection voltage	14.5V/29.0V		12.5V		14.4V
Overcharge recovery voltage	14.0V/28.0V		12.3V		14.2V
Charge voltage	13.8V/27.6V		12.2V		14.2V
Floating charging voltage	13.2V/26.4V		12.0V		14.0V
Overshoot protection voltage	11.0V/22.0V		9.6V		10.4V
Overrelease voltage	12.5V/25.0V		11.1V		12.8V
Low voltage protection voltage	12.0V/24.0V		11.1V		12.8V
Light control turn on lamp voltage	5.0V/10.0V		5.0V		5.0V
Light control lamp voltage	7.0V/14.0V		7.0V		7.0V
Manual switch	Parameters can be modified, default: off, light control mode
Intelligent reduced power	Parameters can be modified, default: yes
Sub-zero charge	Parameters can be modified, default: yes
No-load loss	≤10mA
Working temperature	-35ºC--+65ºC;
Protection grade	IP68
The net weight	0.25Kg
Diameter and length	1.5mm²,≤100mm
Size (length x width x height)	68×84×21mm

Installation and wiring
1. First, the load positive negative pole is connected to the controller corresponding to the red and black line of the lamp. (ignore this step for not using the load);
2. In the same time, the battery is connected to the controller with the battery red and black line, and the controller has three instructions to enter the work.
3. Normal output of the controller, and then the solar panel is connected with the negative pole to the red black line of the panel.
4.Remove the controller sequence from the installation.

State indication

LED indicator	Light color	Indicates	The content status	Function
	Yellow	Discharge	Normally bright	Output normal
			Quick flash	Load short circuit protection
	Red	Battery power	Always bright	Battery is normal
			Quick flash	Over-discharge protection
	Green	Charging	Slow flash	Charging
			Off	Not charged

Note: Voltage parameters can be modified or customized to develop a solar controller.

Load working mode(need to cooperate with my company remote control)
If you set the "manual open " mode, the controller output 24 hours, " intelligent power down" must set "no", and the following set of time and power are invalid.
If the manual mode is set, the controller output is the optical control mode, which can be as follows:
Work time can be divided into five periods, each working time and work power can be adjusted arbitrarily, different combinations can achieve different control modes.

Adjustment item	parameters	Recognition Value	the output current of the factory will be 150mA, and the power adjustment step will be 10%, and the time will be adjusted to 10min.
The first power	0 ~ 100% rated power	100% rated power
The first paragraph	0~999min	360min
Phase 2 power	0 ~ 100% rated power	0
The second period	0~999min	0
Section 3 power	0 ~ 100% rated power	0
The third period	0~999min	0
Section 4 power	0 ~ 100% rated power	0
The fourth period	0~999min	0
Phase 5 power	0 ~ 100% rated power	0
Period 5	0~999min	0

Matters needing attention
1. It is strictly prohibited for the controller to connect the solar panel or load, which may lead to excessive output voltage and the risk of personal electric shock or damage to the controller;
2. The controller has set relevant parameters, and the load ensures that the parameters are aligned with the controller, otherwise it will damage the controller or burn the load.

FAQ
Q1. What's Certificates you have?
A: CE, RoHS, ISO9001, SGS certificates
Q2. How many years warranty?
A: All of products warranty 2 years. If have any quality problem, could return to us exchange new one or repair IR free. Use our company DHL account, free freight.
Q3. What's the payment term?
A: 100% T/T (large order, accept 30% T/T prepay 70% balance before shipping), Western Union, Paypal.
Q4. How's the delivery time?
A: Usually 2 hours after receive full payment. OEM order need 10-15 days.
Q8. How to distinguish solar charge controller with MPPT function?
A: Input voltage more than output voltage, charging current less than loading current.
Q12. What about your sale service?
A: Developing long-lasting relationships with our customers is of utmost importance to us. We are committed to providing you with excellent all-round services, before, during and after the installation of your renewable energy system.

Why Choose Us?
1>Strict Quality Control
For each order, strict inspections will be put in place for each procedure during their processing. The negative products will be ironed out before shipping
2>Stable suppliers
We have cooperated with many accessory suppliers for many years, so we can get cheaper and high quality accessories and thus we can give you a low price and high quality products.
3>Smooth Shipping
We have partnership with excellent shipping forwarders, therefore we can promise fast delivery and have the goods well protected.
4>Customers from all over the world
We have enough experience about foreign trade and our clients can be found in many countries
5>Fast reply
We will respond your question with 8 hours!

Lieferfähigkeit

Verpackung und Versand

Vorlaufzeit:

Hafen:

Verpackungsdetails:

>=5 pieces

US 7.00-8.00

Kontakt

Kommentare

Willkommen bei unzuun Kommentaren! Bitte halten Sie die Gespräche höflich und thematisch. Um produktive und respektvolle Gespräche zu fördern, Sie können Kommentare von unseren Community Managern sehen.

>={ {

US {-{

Details anzeigen