MPPT Charging Electric Solar Power Controller

Produktbeschreibung

I.Main features
1.High efficiency booster MPPT charging, conversion efficiency can reach 99
2. The system uses the solar power supply, does not reduce the battery power quantity
3. Led status indication, the running state is clear
4. Digital tube real-time display charging current, battery voltage and solar input voltage of
5. Complete anti-overcharge, anti-reverse and short-circuit protection functions. One key design, can easily switch 48V, 60V and 72V battery. The system adopts intelligent design, users do not need other settings. Electricity charger and solar charge do not affect each other, can be charged at the same time. Excellent design of dust-proof and heat dissipation, long service life.

‖.Installation and wiring

Connect the "+" of the photovoltaic panel to the red line at the solar end of the controller. (the solar end and the battery end are marked on the face of the controller, please do not connect to the solar end of the cable is φ 4mm.battery end cable φ 2mm.2. Connect the "-" extreme of the photovoltaic panel to the black line at the solar end of the controller. 3. Long press the set button to enter setting mode, set battery voltage. 4. Connect the () pole of the battery to the red line at the battery end of the controller. Connect the battery pole to the black line at the battery end of the controller. After the connection is normal, if there is sun, the controller will start to work. The wiring diagram is shown above.

III. Recommendations for use
The controller should not overload the maximum power of photovoltaic panels using 12V system is 300W, if there are two 18V photovoltaic panels with total power exceeding 300W it is suggested that the maximum power of PV panels using 24V system in series is 600W, and if there are two or more photovoltaic panels, please use in parallel. The working voltage of PV panel is 18V, the open circuit voltage is 22V / 24V, the working voltage of PV panel is 36V and the open circuit voltage is 44V. See the parameters on the back of the photovoltaic panel before connecting.) The controller will be heated during operation. It is recommended that it be installed in a ventilated heat-dissipating environment. When the system is in use, it is suggested to connect a switch between the battery and the controller and between the photovoltaic panel and the controller, otherwise, the phenomenon of ignition will occur during the connection, and the safety of the system can also be guaranteed by connecting the switch. The input and output of the system are designed to be isolated, no co-negative and no co-positive. It is important that batteries are often filled, at least once a month, or they will suffer permanent damage. The battery can be filled only if it enters the battery with more energy than the load uses. Keep this in mind when you configure your system.

IV. System running and status indication
After the system connection is normal, if there is sun, then the system starts up, when the LED lights flicker several times, the digital tube lights up and the system starts up. After the system is started, the digital tube circulates to display the battery voltage, solar energy input voltage, charging current and LED lamp. Status indication, as shown in the following table:

Display	Status	Description
Indicating colo	Red	Solar panel access
Indicating colo	Green	Battery charge
Digital display	b	Cell voltage
	s	Solar panel voltage
	c	Charging current

V. Security recommendations
The controller can adapt 18 V and 36 V photovoltaic panels, please do not use open circuit voltage above 50 V photovoltaic panels, otherwise there is a risk of burning. There are no parts to be maintained and repaired inside the controller, and the inner part contains a voltage higher than the safety of the human body. Please do not disassemble the controller by yourself. Do not put water or corrosive liquid into the controller, this will damage the controller. Whether it is 48V battery, 60V battery and 72V battery, the terminal voltage of the battery exceeds the safety voltage of the human body. When operating, pay attention to the use of insulation tools and keep the necessary dry. When the battery is connected backwards or short-circuited, its current is very large and the controller will not be damaged, but the fuse will fuse and accompanied by a strong fire phenomenon. The impact on the battery and on your equipment will be very strong at this time. When using, please try to avoid this kind of situation. Batteries may produce combustible gas, please stay away from sparks.

VI. Technical parameters

Photovoltaic open circuit voltage	12V~50V
MPPT voltage range	12V~45V
MPPT efficiency	≥99%
Overall efficiency	≥95%
No-load loss	< 5mA
Maximum input power of photovoltaic panel	12V300W,24V600W
Battery	48V/60V/72V
Overcharge protection	48V battery charged with a voltage of 58V, The 60V battery is full of 72V, 72V battery full of 87V
Working temperature	-25ºC~+65ºC;
Weight	0.75Kg
Size	(162-74-66mm)

VII. Failure code description

Fault code	Reason	Solution
E001	Input voltage low	Indoor or cloudy, can work in the sun
E002	Overcharge protection	Stop working, start work below overcharged recovery value
E003	Output open circuit	Connect the corresponding battery
E004	Battery voltage protection	Wait or detect battery voltage is normal

FAQ
Q1. What's Certificates you have?
A: CE, RoHS, ISO9001, SGS certificates
Q2. How many years warranty?
A: All of products warranty 2 years. If have any quality problem, could return to us exchange new one or repair IR free. Use our company DHL account, free freight.
Q3. What's the payment term?
A: 100% T/T (large order, accept 30% T/T prepay 70% balance before shipping), Western Union, Paypal.
Q4. How's the delivery time?
A: Usually 2 hours after receive full payment. OEM order need 10-15 days.
Q8. How to distinguish solar charge controller with MPPT function?
A: Input voltage more than output voltage, charging current less than loading current.
Q12. What about your sale service?
A: Developing long-lasting relationships with our customers is of utmost importance to us. We are committed to providing you with excellent all-round services, before, during and after the installation of your renewable energy system.

Why Choose Us?
1>Strict Quality Control
For each order, strict inspections will be put in place for each procedure during their processing. The negative products will be ironed out before shipping
2>Stable suppliers
We have cooperated with many accessory suppliers for many years, so we can get cheaper and high quality accessories and thus we can give you a low price and high quality products.
3>Smooth Shipping
We have partnership with excellent shipping forwarders, therefore we can promise fast delivery and have the goods well protected.
4>Customers from all over the world
We have enough experience about foreign trade and our clients can be found in many countries
5>Fast reply
We will respond your question with 8 hours!

Lieferfähigkeit

Verpackung und Versand

Vorlaufzeit:

Hafen:

Verpackungsdetails:

>=5 pieces

US 16.00-18.00

Kontakt

Kommentare

Willkommen bei unzuun Kommentaren! Bitte halten Sie die Gespräche höflich und thematisch. Um produktive und respektvolle Gespräche zu fördern, Sie können Kommentare von unseren Community Managern sehen.

>={ {

US {-{

Details anzeigen